Orientation Dependence of the Micro-Pillar Compression Strength in an Electron Beam Melted Ti–6Al–4V Alloy

An α/β two-phase Ti-6 Al-4 V alloy was fabricated by electron beam melting to obtain a basketweave structure.The orientation dependence of the mechanical properties of Ti-6 Al-4 V alloy was studied by micro-pillar compression and post-mortem transmission electron microscopy analysis.The results indicate that different grains have different mechanical responses,and the possible attributions were discussed.Besides the orientation effect,due to the limited volumes of micropillars,the size of the a phases,dispersion of the β phases,and the presence of the free dislocation path also affect the mechanical properties of the micropillars to a large extent.Although no direct link was discovered between the mechanical properties and the parent βorientations,this work provided a promising method to further study the anisotropic mechanical behavior in Ti-6 Al-4 V alloy.     

Removal of copper(II) from aqueous solution using chemically modified fruit peels as efficient low-cost biosorbents

Fruit peels, which are common agricultural byproducts, have been extensively used as abandoned or low-cost biosorbents to remove heavy metals. In this study, dragon fruit peel (DFP), rambutan peel (RP), and passion fruit peel (PFP) were used to remove Cu(II) ions from an aqueous solution. Concentrations of the adsorbed metal ions were determined using the atomic absorption spectroscopic method. Adsorption experiments were performed with different adsorbent dosages, pH values, contact times, and initial copper concentrations. The optimum set of conditions for biosorption of Cu(II) ions was found to be an adsorbent dosage of 0.25 g, a contact time of 180 min, an initial concentration of 100 mg/L, a pH value of 4 for RP and PFP, and a pH value of 5 for DFP. The adsorption conformed with the pseudo-second-order kinetic model. The adsorption data were consistent with the Langmuir and Freundlich isotherm models, but the best fit was with the Langmuir model. The Langmuir monolayer adsorption capacity values of DFP, RP, and PFP were calculated to be 92.593, 192.308, and 121.951 mg/g, respectively. RP showed a higher adsorption capacity of Cu(II) ions than PFP and DFP for all parameters. The results indicate that these biosorbents might be used to effectively adsorb Cu(II) ions from wastewater treatment plants.     

Optimizing the Optoelectronic Properties of Face-On Oriented Poly(3,4-Ethylenedioxythiophene) via Water-Assisted Oxidative Chemical Vapor Deposition

Engineering the texture and nanostructure to improve the electrical conductivity of semicrystalline conjugated polymers must address the rate-limiting step for charge carrier transport. In highly face-on orientation, the charge transport between chains within a crystallite becomes rate-limiting, which is highly sensitive to the π–π stacking distance and interchain charge transfer integral. Here, face-on oriented semicrystalline poly(3,4-ethylenedioxythiophene) (PEDOT) thin films are grown via water-assisted (W-A) oxidative chemical vapor deposition (oCVD). Combining W-A with the volatile oxidant, antimony pentachloride, yields an optimized electrical conductivity of 7520  ±  240 S cm⁻¹, a record for PEDOT thin films. Systematic control of π–π stacking distance from 3.50 Å down to 3.43 Å yields an electrical conductivity enhancement of ≈ 1140%. The highest electrical conductivity also corresponds to minimum in Urbach energy of 205 meV, indicating superior morphological order. The figure of merit for transparent conductors, σ_dc/σ_op, reaches a maximum value of 94, which is 1.9 × and 6.7 × higher than oCVD PEDOT grown without W-A and utilizing vanadium oxytrichloride and iron chloride oxidizing agents, respectively. The W-A oCVD is single-step all-dry process and provides conformal coverage, allowing direct growth on mechanical flexible, rough, and structured surfaces without the need for complex and costly transfer steps.     

Ultrathin perovskite based solar cells with the efficiency enhanced by charge transfer process

We report a new approach of improving the solar cells efficiency based on ultrathin perovskite films. We propose the addition of CuPc compound to perovskite active layer for enhanced charge generation and transfer process by charge transfer process between CuPc and perovskite. The performance of the devices with and without addition of CuPc was studied in respect to thickness of the active layer. The thickness was varied by the change of the spin coating speed in the range of 4000, 7000 and 10000 rpm, different concentration of CuPc also been studied. The process of charge carrier recombination, crystallinity and Raman characteristics of the obtained films was studied. The perovskite device with an active layer of MAPbI₃ mixed with CuPc spin coated with the speed of 10000 rpm with thickness of about 150 nm demonstrated the efficiency of 12.7%. The ultrathin mixed perovskite film (10000 rpm perovskite film of 15% CuPc) based device presents 33% thickness and 85% efficiency of common pure perovskite device (4000 rpm pure perovskite film).     

Ytterbium (III) oxide reinforced novel TeO2–B2O3–V2O5 glass system: Synthesis and optical,structural, physical and thermal properties

Different samples of xTeO₂.(25-y)B₂O₃.zV₂O₅.yYb₂O₃ (or TBVY) new glass material were synthesized by the classical melt-quenching method. Structural, optical, physical, and thermal analyses of the synthesized glasses were performed in addition to Monte Carlo simulation to test radiation shielding properties. The results showed that increasing ratios of Yb₂O₃ (y = 0.0, 0.5, 1.0, and 1.5 mol%) produced monotonic density values of the synthesized glasses ranging from 4.70058 g cm^?3 to 5.01038 g cm^?3. XRD and FTIR analyses were used to confirm the glass structure of all samples. Optical transmittance and absorption parameters varied almost monotonically with increasing ratios of Yb₂O₃ indicating the ability to predict and control these properties using Yb₂O₃ additive. Furthermore, simulated radiation interaction parameters, such as attenuation coefficients and half-value layer, exhibited well-behaved dependence on the concentration ratio of the Yb₂O₃ additive. This approach to glass material synthesis demonstrate the useful synergetic effect of combining structural, optical, and radiation characteristics.     

Comprehensive study on structural,thermal, morphological and luminescence (RL,PL, TL) properties of CaLa2(WO4)4: Tb3+, Dy3+ phosphors synthesized via sol-gel method

Tb³⁺/Dy³⁺ co-doped CaLa₂(WO₄)₄ (CLW: Tb³⁺/Dy³⁺) and its derivatives were synthesized by the sol-gel method. The morphology, thermal, structure and luminescent-optical properties the as-prepared light-emitting phosphors were characterized by utilizing scanning electron microscopy (SEM), differential thermal analysis (DTA)-thermogravimetric analysis (TG), X-ray diffraction (XRD) and radioluminescence (RL or X-ray luminescence) - photoluminescence (PL) –thermoluminescence (TL or TSL) - optical absorption spectrometry. The Tb³⁺ and Dy³⁺ ions were singly or doubly doped and the results were examined in detail. Moreover, for these phosphors, the energy transfer mechanisms which depend on RL and PL spectra were determined. The samples excited by X-ray demonstrate characteristic luminescence peaks of Dy³⁺ (422, 480, 575, 663 and 747 nm) and Tb³⁺ (489, 544, 586, 620, 652 and 675 nm). These emissions are similar for RL and PL measurements. It could be said that the energy transfer efficiency of the host material is perfect for rare-earth ions. The synthesized phosphors exhibit various colors from yellow to blue under UV excitation. The optical band gaps of host CLW, CLW: Tb³⁺, CLW: Dy³⁺ and co-doped CLW: Tb³⁺/Dy³⁺ were calculated at values 3.83 eV, 3.44 eV, 3.64 eV and 3.52 eV, respectively. From the results obtained, the CaLa₂(WO₄)₄: Tb³⁺, Dy³⁺phosphors may be one of the potential candidates for light-emitting diode.     

Synthesis of strontium (Sr) doped hydroxyapatite (HAp) nanorods for enhanced adsorption of Cr (VI) ions from wastewater

The development of high-efficiency adsorbents for heavy metal ion removal from wastewater is highly desirable and challenging due to their synthesis complexity and low adsorption capacities. Herein, we reported the synthesis of strontium (Sr) doped hydroxyapatite (HAp) for the increased Cr (VI) adsorption. The effects of pH, temperature, and time on adsorption performances were studied. As a result, the Sr-HAp nanorods can achieve a Cr (VI) adsorption capacity of 443 mg/g, which is significantly higher than that of HAp nanorods (318 mg/g). To better understand the adsorption mechanism, the Langmuir isotherm model was established. The modeling results indicated that Langmuir monolayer chemical adsorption contributed to the efficient Cr (VI) ion removal for Sr-HAp nanorods adsorbents. The surface area and surface functional groups (O–H) contributed to the different Cr (VI) adsorption capacities between HAp and Sr-HAp.     

Therapeutic Potential of AAV1-Rheb(S16H) Transduction against Neurodegenerative Diseases

Neurotrophic factors (NTFs) are essential for cell growth, survival, synaptic plasticity, and maintenance of specific neuronal population in the central nervous system. Multiple studies have demonstrated that alterations in the levels and activities of NTFs are related to the pathology and symptoms of neurodegenerative disorders, such as Parkinson’s disease (PD), Alzheimer’s disease (AD), and Huntington’s disease. Hence, the key molecule that can regulate the expression of NTFs is an important target for gene therapy coupling adeno-associated virus vector (AAV) gene. We have previously reported that the Ras homolog protein enriched in brain (Rheb)–mammalian target of rapamycin complex 1 (mTORC1) axis plays a vital role in preventing neuronal death in the brain of AD and PD patients. AAV transduction using a constitutively active form of Rheb exerts a neuroprotective effect through the upregulation of NTFs, thereby promoting the neurotrophic interaction between astrocytes and neurons in AD conditions. These findings suggest the role of Rheb as an important regulator of the regulatory system of NTFs to treat neurodegenerative diseases. In this review, we present an overview of the role of Rheb in neurodegenerative diseases and summarize the therapeutic potential of AAV serotype 1 (AAV1)-Rheb(S16H) transduction in the treatment of neurodegenerative disorders, focusing on diseases, such as AD and PD.     

A Comprehensive Review of Genetically Engineered Mouse Models for Prader-Willi Syndrome Research

Prader-Willi syndrome (PWS) is a neurogenetic multifactorial disorder caused by the deletion or inactivation of paternally imprinted genes on human chromosome 15q11-q13. The affected homologous locus is on mouse chromosome 7C. The positional conservation and organization of genes including the imprinting pattern between mice and men implies similar physiological functions of this locus. Therefore, considerable efforts to recreate the pathogenesis of PWS have been accomplished in mouse models. We provide a summary of different mouse models that were generated for the analysis of PWS and discuss their impact on our current understanding of corresponding genes, their putative functions and the pathogenesis of PWS. Murine models of PWS unveiled the contribution of each affected gene to this multi-facetted disease, and also enabled the establishment of the minimal critical genomic region (PWScr) responsible for core symptoms, highlighting the importance of non-protein coding genes in the PWS locus. Although the underlying disease-causing mechanisms of PWS remain widely unresolved and existing mouse models do not fully capture the entire spectrum of the human PWS disorder, continuous improvements of genetically engineered mouse models have proven to be very powerful and valuable tools in PWS research.     

Three-parameter (3P) weibull distribution for characterization of strength of ceramics showing R-Curve behavior

Strength distribution of advanced ceramics is commonly characterized by two-Parameter (2P) Weibull distribution. However, deviation of strength distribution from 2P-Weibull distribution may occur in ceramics due to various mechanisms. R-curve behavior is one of these mechanisms where increase of fracture resistance with the extension of crack occurs. In such cases, 2P-Weibull distribution may not be the best fitting distribution function based on the goodness-of-fitness tests. This article examines the effectiveness of three-parameter (3P) Weibull distribution function for fitting the strength variation due to R-curve effect by using experimental and virtual strength data. The effect of Weibull parameters, degree of increase in crack resistance and number of samples on effectiveness of fitting via 3P-Weibull distribution is investigated. It is reported that 3P-Weibull distribution function fits the strength distribution better than 2P-Weibull distribution function for materials showing R-curve behavior when the crack resistance curve is steep and Weibull modulus is high. Furthermore, it is shown that at least 100 samples should be used for a reliable estimate when the material exhibits R-curve behavior.